Cane Corso became popular because it is perfect in the Merchant satellite rights in the contemporary world. It combines the dedication and extraordinary sensitivity, rapid ponimanimanie rules and regulations, the amazing adaptation to life in urban environments. Cane Corso – perfect for silent but understanding each other. Cane Corso can spend hours to be around, lie at the feet of the host, without interfering with his work. It is worth special attention and conflict Cane Corso in contact with other animals and people, it seems that her dignity does not allow her to sink to small skirmishes. Balanced character of Cane Corso, however, will continued only for as long as the dog does not feel a threat to the host and his relatives. Although it is unusual that a dog that was bred in poor rural areas of Italy, became a symbol of respectability in our time, but there is no doubt that the breed Cane Corso waiting more glorious and celebrated the future.
If necessary, apply chock tool (reeling out the ax, snap). The resulting product, in this way is called forging. Form, and the more weight forgings may vary (eg, weight forgings can up to 350 tons and more). The difference is that small and medium-sized forgings are made from rolled billets and large – from ingots. The most widely forged to get air and vapor-air hammers.
Small size of workpiece is treated with pneumatic hammers. The principle of a pneumatic hammer: there are two interconnected cylinders, the working and the compressor. In the role of the elastic connection acts air that is blown piston alternately in the upper and the lower part of the working cylinder, which drives the firing pin, which begins to strike the workpiece. Blows per minute firing pin can be anywhere from 95 to 225. Weight incident of this hammer can reach 1000 kg. Switchgear helps keep the striker at the top or bottom positions. Started work in the hammer with an electric motor.
Vapor-air hammers double actions are used for processing forgings of medium size, having a mass of up to 3 m. The falling of a hammer of mass 1 – 5 tons driven by steam power or compressed air, the frequency of beats per minute – 30 to 60. To work large forgings needed press – hydraulic or parogidravlicheskie. The principle of the hydraulic press is based on the law of Pascal. There is a transfer pressure of up to 20 MPa, was created in the working cylinder, the workpiece through the plunger, Traverse, the firing pin. Parogidravlicheskie different from hydraulic press so that they have a multiplier that can increase pressure to 60-80 psi. Water is supplied to the working cylinder of multiplier. Unique to the modern presses can handle bars up to 500 tons, because such media are operating force until 2000 meganyutonov. Designed to process the workpiece is placed between the movable upper and lower fixed strikers press or hammer. The direction of deformation, or, in other words, the flow of the metal blanks indicate the surface dies and bed-tools, which are in contact with him. When pulling cross-section of workpiece decreases and its length – is increasing. Billets have across dies, moves and Kant it 90 degrees after each compression. First forge a square, while the rate of deformation is the large, and then, if necessary, preparation or rounding the form. To speed up the curved broach used rolling and brisk, which increase the elongation of one compression. In the process of forging a metal workpiece in precipitation increased cross-section due to altitude. When bending the workpiece is clamped between the strikers hammer, you need a local heating of the workpiece. To obtain the same section and place the bend, and the entire length of the workpiece, pre-planting to do – draft of the piece. To flash the holes in the workpiece up to half its thickness proshiven hammered, then harvest should be reversed, and punch a hole through it. Barrel arbor helps to align or expand the hole. Otrubka done with axes. To smooth out small-scale forgings used trowels and large – with the help of light strikes the hammer dies. Can be used to furnish suitable crimping. You can understand even if you're a person, that the process of forging is not easy, but what we can contemplate the beauty in the form of a variety of forged products!
Join the North Carolina Jamboree
In North Carolina the Scouts movement is very popular among the youth. Every year many hundreds of kids congregate together to share some great times at the North Carolina Youth Jamboree. At this amazing even the Boy Scouts of America are joined by North Carolina 4H Club, Boys and Girls Clubs, Girl Scouts of America, and the Fellowship of Christian Athletes.
The goal of the Jamboree is to showcase the incredible programming which inspires and motivates kids to be and do the best that they can. The Scouts also have in mind to recruit new members, to develop future leaders, and to visit the various public and private youth agencies. But most of all the Scouts of North Carolina are there to have fun.
The Jamboree usually accommodates seven thousand participants, but there is no charge to join. However, each person who does come is asked to kindly bring one canned food item to be donated to a local charitable organization. Participants can either bring their own food for the gathering, or partake in the food that is available on site.
Major sponsors of the Youth Jamboree are: NC Dept of Agriculture and Consumer Services, Blue Cross Blue Shield of NC and the General Hugh Shelton Leadership Center.